Storing and displaying cigarette cards
Keep cigarette cards in pocketed pages made of a stable plastic such as polypropylene or polyester, in a binder stored somewhere cool, dry and dark. Avoid old slot-in albums, soft PVC, rubber bands and any kind of glue, and frame cards so that they can be taken out again unharmed.
What damages cards
Cigarette cards are small pieces of printed board, most of them eighty to a hundred and thirty years old. The threats are the same as for any paper:
- Handling. Corners are the first thing to go, and collectors judge a card by its corners.
- Damp. It causes foxing, the brown spotting seen on old paper, and makes gummed backs stick to whatever they touch.
- Light. Daylight fades colour printing, and the reds and blues of lithographed cards go first.
- Bad materials. Acidic paper, soft plastics, sticky tape and rubber bands all leave marks that cannot be removed.
The general principles are covered in storing and displaying a collection. What follows is specific to cards.
Why the old slot-in albums damage corners
For decades the standard cigarette card album had thick paper pages with four diagonal slits for each card. You tucked each corner into a slit. It looked neat, but it is the reason so many otherwise clean cards have bent or creased corners. Every time a card is put in or taken out, each corner is flexed, and the cut edge of the slit presses a line across it over the years.
If you inherit cards in a slot-in album, they are safe to leave while you decide what to do, but remove them carefully if you plan to keep them. Ease the page slit open and slide each corner out flat. Never pull the card upwards.
Albums with printed spaces for gummed cards are a different case. Cards stuck into those should stay where they are, as explained in what cigarette cards are worth.
Modern pages and sleeves
The usual choice today is a ring binder with clear pocketed pages. Each card sits in its own pocket, both sides can be read without touching it, and nothing grips the corners. Pages are made with pockets for standard cards, typically ten to a page, and with larger pockets for large cards.
| Material | Safe for long-term storage | Notes |
|---|---|---|
| Polypropylene | Yes | The common material for card pages. Inexpensive and stable. |
| Polyester (often sold as Mylar or Melinex) | Yes | The archival standard. Very clear and rigid, and dearer. |
| Polyethylene | Yes | Stable but softer and less clear. |
| Soft PVC | No | Contains plasticisers that can migrate, leaving cards sticky or lifting ink. Often has a strong plastic smell. |
Look for pages described as free of PVC, plasticisers and acid. If an old page feels oily, smells strongly or has gone yellow and wavy, replace it.
Practical points that save trouble later:
- Buy the right pocket size. A card should slide in without force and not rattle about. Cards vary slightly between makers, so test before buying pages in bulk.
- One card to a pocket. Two back to back hides the text and can cause gummed backs to stick together.
- Do not overfill binders. An overfull binder bows the pages and bends the cards nearest the rings. A binder with a slipcase keeps dust and light out.
- Stand binders upright, like books. Stacked flat, the weight presses on the cards at the bottom.
Loose cards and duplicates
Complete sets waiting for a page, and duplicates for swapping, are best kept in small boxes made of acid-free card, with the cards standing on edge and a slip of card between sets.
Do not use rubber bands. They cut into the edges of the outer cards, and as the rubber perishes it melts on to the card and stains it. Paper clips leave rust marks and dents.
Handling
Wash and dry your hands, and hold cards by the edges. Clean bare hands are usually better than gloves for something this small, because gloves make you clumsy and corners suffer. Do not try to clean cards: rubbing with an eraser or a damp cloth removes surface finish, and it shows.
Framing without glue
A set of 25 or 50 cards looks very good framed, and it is the most popular way to enjoy them. The rule is that framing must be reversible. A framed set that has been glued or taped down has lost most of its value, exactly as a stuck-down album has.
- Use a mount cut with an aperture for each card, with the cards held behind the windows by a backing board or in clear pockets. No adhesive should touch a card.
- Ask for conservation-grade, acid-free mount board and backing.
- A double-sided frame, glazed front and back, lets the backs be read. Framers who work with cards and medals know the method.
- Choose glazing that filters ultraviolet light. It slows fading but does not stop it.
- Hang the frame away from direct sunlight, radiators, bathrooms and outside walls that get cold and damp.
If a set is scarce or in fine condition, frame a lesser duplicate and keep the best one in a binder.
Where to keep the collection
A shelf in a room you live in is ideal: steady temperature, moderate humidity and no direct sun. Lofts, garages, cellars and sheds are the worst places, because they swing between hot and cold and are often damp.
Keep a list of what you have. It makes buying easier and matters for insurance, as described in how to catalogue a collection.
Related guides
- Storing and displaying a collection
- Cigarette cards: the collector's guide
- Tea cards and trade cards, which are stored in the same way
- Insuring a collection
- Collection tracker: a free private inventory in your browser